Apple CS II Uživatelská příručka Strana 261
- Strana / 386
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
and 3) the video cable exhibits lower capacitance between the center lead and
the shield.
You can connect your Apple II to a Monochrome or Color composite video
monitor.
______________________________
From: Michael Pender and Rubywand
018- What is the usual way to connect an Apple II to a
display?
For a IIgs, you connect to the IIgs RGB monitor. For other Apple II's, you
use a video quality 'RCA cable' to connect to a composite color monitor, such as
one of the Apple II monitors or a third party monitor like the Amdek Color-1.
(The IIgs has a composite color output which can go to a composite monitor; but,
for IIgs super-res, the results are unsatisfactory.)
An alternative to a composite monitor is to connect to a color TV directly
or through a VCR. Most VCRs and many modern televisions have a composite video
input port. Rather than buying a new monitor, a person can usually use an RCA
cable to connect the Apple to a spare VCR or television. The stabilization
logic built into even a cheap VCR can go a long way toward cleaning up an ugly
picture.
______________________________
From: Rubywand
019- Does anybody know how to do the "Color Killer Mod"
on a //e?
It looks like you should be able to do a full-screen color-killer on a IIe
by using a general purpose NPN transistor (2N3904, 2N2222, etc.) to shunt the
Color Burst signal. The transistor's collector would connect to the junction of
R15 and R13; the emitter lead would go to Ground. The transistor should be
connected directly to the R15-R13 junction and ground.
The base lead would go through a 2k-3k Ohm resistor to an annunciator
output, such as An-3 at pin 12 on the 16-pin J-15 Game connector. PEEKing the
appropriate addresses should flip Color OFF and ON.
The reason for qualifiers such as "looks like", etc. is that I have not
actually tried a mod like this on a IIe. Monitors are remarkably sensitive to
Color Burst. If the transistor does not do a good job of shunting the signal,
enough may get through to trigger Color-ON.
A more positve (but less easy) technique is to use a 74LS32 OR gate to
control flow of the 3.58MHz signal. The IC could be tack-soldered onto U88 via
its +5 and GND pins. U88 is the 74S02 which has the gate which produces Color
Burst.
- Accelerators 1
- RAM chips? 14
- Applications 24
- I get them? 26
- 10 IIgs's connected 32
- Apple ][? 34
- BASIC on my PC? 40
- .reg for executing 41
- DOS & ProDOS 51
- DOS command? 55
- DOS 3.3 file? 61
- II telecom utility? 67
- 024- What is ProDOS? 67
- Diskettes 78
- 010- How can I copy disks? 84
- Main Error List 87
- Floppy Disk Drives 109
- Disk ][ drive? 110
- Disk ][ controller card? 125
- File Utilities 132
- Apple II? 134
- .dsk and .2MG disk images? 151
- Apple II game? 158
- Apple II users? 166
- Hardware Hacking 179
- 09010001. Is there a fix? 183
- What is the board for? 188
- IIe motherboard? 191
- 029- What is the C-One? 197
- How can I re-whiten them? 197
- History 202
- Input Devices 222
- Where can I get one? 224
- Tablet? 236
- Flight Stick? 243
- Anyone have a fix? 248
- Monitor 249
- RGB Monitor? 255
- IIgs monitor? 258
- Laser 128? 264
- Power Supplies & Cooling 272
- Printers & Interfaces 293
- Sound & Music 308
- Apple II and a PC? 335
- Modem" cable? 340
- Serial Interface card? 350
- Which cable? 350
- II sites? 359
- Zip Drives & Tape 372
- Will this damage anything? 377
- 80 tape 385
Desa VDDVF36STN/STP manuels
Manuels d'utilisation et guides de l'utilisateur pour Foyers Desa VDDVF36STN/STP.
Nous fournissons des manuels en pdf 1 Desa VDDVF36STN/STP à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce